1.1 SUMMARY A. Section includes: Furnish Precast Concrete indicated on drawing or specified herein. 1.2 REFERENCES A. American Society for Testing & Material 1. ASTM C33 2. ASTM C150 3.ASTM C31 1.5 SUBMITTALS A. Submit Product data,shop drawings and samples. 1. Product Data: Manufacturer’s specifications and technical data edited specifically for proposed system, including the following specific Information: a: Detailed specification of construction fabrication. b: Manufacture’s installation instructions c: Maintenance literature d: Product warranty 2. Shop Drawings: Indicate pertinent dimensions, general construction, component connections anchoring methods, hardware and installation procedures. 3. Samples as requested by Architect.
1.6 QUALITY ASSURANCE A. Qualifications of Manufacture: Manufacturer to be prequalified by specifier prior to bidding. Failure to comply will result in disqualification of bid. Manufacturer to have at least five years experience in the manufacture of precast concrete field proven for at least five years.
1.10 WARRANTY Manufacturer shall submit a written warranty for precast products for the period of two years upon acceptance.
2.1 MANUFACTURERS A. Clarification Note: Drawings and installation specification are based on manufactures proprietary literature from us. Other manufacturers shall comply with minimum levels of material and detailing indicated on drawings of specified herein. B. All Precast products for this project shall be of one manufacturer.
2.2 MATERIALS A. Portland cement: ASTM C150 specifications for Portland cement. B. Aggregates: All aggregates to meet ASTM C33 specifications, to be cleaned of foreign matter and properly graded to size. C. Coloring: Pigments used shall be inorganic,resistant to alkalinity and used as per manufacturers recommendations.
HYPEL™ LLDPE 3170 UV 8 NATURAL ** LINEAR LOW DENSITY POLYETHYLENE, 7.0 MFI
TYPICAL PROPERTY VALUES†
PROPERTY
METHOD
UNIT
VALUE
PHYSICAL
Specific Gravity
ASTM D792
0.935
Metal flow (190°C / 2.16 kg)
ASTM D1238
g/10 min
7
MECHANICAL @ 73°F
Tensile Strength at Yield
ASTM D638
psi
2720
MPa
18.8
Flexural Modulus - 1% Secant
ASTM D790
psi
100,000
MPa
655
ARM Impact 1/8" (Notched) @-40°C
ASTM D562B
ft-lb/in
79
Hardness (Shore D)
ASTM D785
-
-
THERMAL
264 psi - ASTM, 1.80 MPa-ISO
ASTM D648
°C
35
°F
95
66 psi - ASTM, 0.45 MPa-ISO
ASTM D648
°C
52
°F
125
OTHER
ESCR (100% IGEPAL)
>1000
**When used unmodified for food contact applications, this copolymer will comply with the U.S. Food and Drug Administration Food Additive Regulation 21 CFR 177.1520(c)3.1a. This section does not include use in packing or holding food during cooking. This product is limited to use in contact with food only under the conditions of use C through H described in table 2 of Sec. 176.170(c), and when contacting fatty foods of Types III, IVA, V, VII-A, and IX described in table 1 of Sec. 176.170(c), the finished articles are to have a volume of at least 18.9 liters (5 gallons). The uses cited are subject to good manufacturing practices and any limitations, which are part of the regu- lations. The regulations should be consulted for complete details.
†The data listed here fall within the normal range of product properties, but they should not be used to establish speci- fication limits or used alone as a basis for design. This information is not intended as a warranty of any kind. Buyers must make their own representative test and assume all risks of use, whether used alone or in combination with other products. Entec Polymers, LLC assumes no obligation or liability of any advice furnished by it or results obtained with respect to these products. All warranties expressed or implied including warranties of merchantability for a particular purpose or use are excluded and disclaimed. Entec Polymers, LLC assumes no liability for use of products in infringe- ment of any patent. The foregoing limitation of remedy and exclusion of liability is reflected in and is part of the consideration for the price, at which the products are sold by Entec Polymers, LLC. All data displayed herein has been obtained via testing of injected molded specimens of natural color. Pigmentation may affect certain properties to various degrees.
Concrete Recycling Centers, Concrete Trash Receptacles, Concrete Recycling Waste Receptacles, Trash Receptacles, Metal Trash Receptacles, Steel Trash Receptacles, Weathergard, Polysteel, Streetscape, Aspen Series, and American Series from your source for material handling equipment.
