Simple lines and colors make these tables an excellent choice for an outdoor café or park area. High quality, low maintenance.
Accepts optional umbrella without extra stand. New and improved for easier assembly. Supersedes TF3125. Also available in two seat and three seat models. ALSO-- REFINISHING KIT: TF3315 Make your table look NEW!! All the materials you need to refinish your concrete tables, benches, and seats to restore them to like new condition.
- 2 lbs Grout Mixture - 10 oz Bonding Agent - 4 Spray Cans of Sealer
Additional Items Needed:
- Rubber Gloves - #240 Sand Paper - Sanding Block - Mixing Tool - Scrubbing Pad
- #80 Grit Sand Paper - Pail - Sponge - Squeegee
Note: Wear rubber gloves during entire refinishing process. Refinishing results are best when all excess grout is removed and surface is sanded smooth. Check for and clean up spills after each step. Newly refinished tables will retain an attractive appearance for several years if they are resealed at least once a year.
1. Scrub and Rinse Rinse surface with water while using scrubbing pad to remove dirt and grime. Using the sanding block and #80 sand paper, sand surface. Repeat rinse.
2. Grout Mix grout and bonding agent together to create a creamy consistency in a pail. Allow to set for 5 minutes Apply to the surface using a circular motion, with a sponge to fill all voids. Can be used on smooth edges, not on acid wash surfaces.
Note: Acid wash edges to be taped off before groutin the surface to avoid getting grout in pores of edge.
3. Remove Excess Grout Immediately remove all excess grout with a squeegee. Apply water as needed to keep grout moist with a spray bottle. Thoroughly inspect the surface to be certain it is clean. Allow to cure for approximately 24 hours.
4. Wet-Sand Once the surface has cured, wet-sand grouted surface using sanding block, #240 sandpaper and water.
5. Clean Thoroughly rinse with water and allow to dry. Surface must be dust free. If tape was needed for edges remove tape before cleaning the surface.
4. Wet-Sand Once the surface has cured, wet-sand grouted surface using sanding block, #240 sandpaper and water.
SPECIFICATION
1.1 SUMMARY A. Section includes: Furnish Precast Concrete Table indicated on drawings or specified herein.
1.2 REFERENCES A. American Society for Testing & Materials 1. ASTM C33 2. ASTM C150 3. ASTM C31
1.5 SUBMITTALS A. Submit product data, shop drawings and Samples. 1. Product Data: Manufacturer's specifications and technical data edited specifically for proposed system, including the following specific information: a. Detailed specification of construction fabrication. b. Manufacturer's installation instructions c. Maintenance literature d. Product warranty 2. Shop Drawings: Indicate pertinent dimensions, general construction, component connections anchoring methods, hardware and installation procedures. 3. Samples as requested by Architect.
1.6 QUALITY ASSURANCE A. Qualifications of Manufacturer: Manufacturer to be pre-qualified by specifier prior to bidding. Failure to comply will result in disqualification of bid. Manufacturer to have at least five years experience in the manufacturer of precast concrete tables field proven for at least five years.
1.10 WARRANTY Manufacturer shall submit a written warranty for precast products for the period of two years upon acceptance of products.
2.2 MATERIALS A. Portland Cement: ASTM C150 specifications for Portland Cement. B. Aggregates: All aggregates to meet ASTM C33 specifications, to be cleaned of foreign matter and properly graded to size. C. Coloring: Pigments used shall be inorganic, resistant to alkalinity and used as per manufacturers recommendations.
Concrete Round Table, Concrete Tables, Park Furnishings, Tables, Concrete and Steel Tables, Plastic Picnic Table, Polysteel Tables, Site Amenities, Site Furnishings, Steel Tables, and Street Furniture from your source for material handling equipment.
