Gilmore-Kramer Company Material Handling Equipment - 1-800-544-3137 - Service - Installation - Custom Fabrication
Home Order Search Quote Info About Us My Account Shopping Cart
    Categories
Back to Product Category

WS-500 - WS-501 - WS-502
ALUMINUM PLANTERS

The Executive Series

The Executive Series includes powder coated
aluminum planters that add structure and distinction
to any site's aesthetics. Their durability makes them
an excellent choice for both indoor and outdoor use.
Optional foot pads & drainage holes available upon
request.

Drain Hole: Optional, upon request
Material: Aluminum
Shape: Square

Order Online, by Phone, or by E-Mail

~ Add items to your online shopping cart ~
Click the Model No. of the item you wish to purchase.


PRICES
Model No.
Size (Tapered)
Weight
Price
36" x 36" x 36"
155 lbs
$2,100.00
30" x 30" x 30"
115 lbs
$1,772.30
24" x 24" x 24"
85 lbs
$1,572.30
Note: Need to choose with or without drain hole

METAL POWDERCOAT COLORS AVAILABLE

WS-500 Drawing

WS-501 Drawing

WS-502 Drawing

TECHNICAL INFORMATION - POWDURA® Epoxy Powder Coating
PRODUCT DESCRIPTION
EAS6-00025
ZINC RICH PRIMER

POWDURA® Epoxy Powder Coating is recommended for a broad range of interior functional and
decorative applications.

APPLICATION

Cure Schedule: 10 min @ 205°C (401°F)
Film Thickness Range: 1.5-1.8 mils

ATTRIBUTES

Specific Gravity: 2.83 +/-0.05
Coverage at 1.0 mil: 67.8 sq.ft/lb
60 Gloss: Visual
Adhesion: No Failure with 1/16in. squares (5B) (ASTM D-3359)
Flexibility: Pass 1/8" Mandrel Bend (ASTM D-522)
Pencil Hardness:
H-2H (ASTM D-3363)
Impact Resistance(dir/rev): 160/160 (ASTM D-2794)

Other Notes

SaltSpray Performance: When top coated with TGIC polyesters,urethanes and fluoroploymers, testing showed
4-5 mm undercut at 5000 hours on Bonderite 1000

Storage:
POWDURA® Powder Coatings should be kept in a dry and cool area at temperatures below 80°F (26.7° C). Shelf
life is approximately 12 months.
When not in use, store powder in sealed containers: fine powders are hygroscopic.

Substrate Preparation
General: Substrate should be free of grease, oil, dirt, fingerprints, drawing compounds, any contamination, and surface
preparation treatments to ensure optimum adhesion and coating performance properties. The use of a chemical
conversion coating prior to the application of a powder coating is strongly recommended. Consult Metal Preparation
Brochure CC-T1 for additional details.

Aluminum: A minimum of a 5-stage chrome phosphate metal treatment, or equivalent, is required for good adhesion
and optimum coating performance properties.

Testing:
Due to the wide variety of substrates, surface preparation methods, application methods, and environments, the
customer should test the complete system for adhesion and compatibility prior to full-scale application. The properties
listed are typical and should not be construed as the actual specification.

Product Limitations:
Contact your Sherwin-Williams Representative where use of this product at higher than recommended film thickness
may be required.

APPLICATION:
Powder coatings must be applied using suitable electrostatic equipment. Consult your Sherwin-Williams
Representative regarding unique applications.

CAUTIONS:
Thoroughly review product label for safety and cautions prior to using this product. Please direct any questions or
comments to your local Sherwin-Williams facility.

CAUTION!
Causes eye irritation, causes skin irritation, may cause allergic skin reaction, respiratory irritant, dust
may cause eye and respiratory irritation, dust may form an explosive mixture in air. Avoid breathing dust. Avoid
contact with eyes and prolonged or repeated contact with skin. Use protective clothing and NIOSH approved
respirator. Do not use near sparks or open flame or any type of ignition source. Wash thoroughly after handling.
Use only with adequate ventilation.

FIRST AID:
If on SKIN: Wash thoroughly with soap and water.
If in EYES: Flush with water immediately and procure medical attention. The area adjacent to the coating operation
should be properly ventilated. Cure ovens must be exhausted to the outside atmosphere. All dusts are respiratory
irritants, inhalation of the dust should be avoided. To avoid static electricity buildup, properly ground all equipment.
Provide dust collection equipment with adequate explosion venting; dust clouds of any finely divided organic material
can be ignited by open flame or electrical sparks.

DO NOT TAKE INTERNALLY. KEEP OUT OF REACH OF CHILDREN. FOR INDUSTRIAL USE
ONLY. REFER TO MATERIAL SAFETY DATA SHEET FOR ADDITIONAL INFORMATION.


Note:
Product Data Sheets are periodically updated to reflect new information relating to the product. It is important that the
customer obtain the most recent Product Data Sheet for the product being used. The information, rating and opinions
stated above pertain to the material currently offered and represent the results of tests believed to be reliable.
However, due to variations in customer handling and methods of application which are not known or under our
control, The Sherwin-Williams Company cannot make any warranties or guaranties as to the end results.

Aluminum Planters, Metal Planters, Planters, Security Planters, Polysteel Planter, Commercial Planter, Steel Security
Planters, Flower Planters, Site Furnishings, and Steel Planters from your source for material handling equipment.

Back to Product Category
Home - Order - Search - Quote- Info - About Us - My Account - Shopping Cart