Gilmore-Kramer Company Material Handling Equipment - 1-800-544-3137 - Service - Installation - Custom Fabrication
Home Order Search Quote Info About Us My Account Shopping Cart
    Categories
Back to Product Category

MODEL CRB
HORIZONTAL BELT CONVEYOR
(Troughbed Roller Bed)
The Model “CRB” is ideally used in scrap
handling and recycling operations. The
roller bed with deep troughed construction
can carry “culled” or broken glass,
cans, wood chips, aluminum, steel,
plastic stampings, etc. The “CRB” is
widely used in recycling operations as an
“Environmental Conveyor.”
horizontal belt conveyors
7 belt widths
Self-cleaning tail pulley
Troughed Guard Rails
Adjustable MS-type floor supports
   available
Side mounted drive for low elevations
belt conveyors
STANDARD SPECIFICATIONS
BELT–BlackTrackmate 533 COS. Clipper lacing. RETURN IDLER–Adjustable 1.9 in. dia. pre-
    lubricated bearings.
BED–Roller bed with 2 in. dia. x 12 ga. unplated
    tread rollers spaced every 6 in., or 12 in. mounted
    in 10 ga. painted formed steel channel frame with
    12 ga. painted side guards extending 8-1/2” above
    belt. Sections bolt together with splice plates.
TAKE-UP–Screw take-ups at tail pulley. Provides
    4 in. of belt take-up.
BEARINGS–Sealed, pre-lubricated, self-aligning,
    cast-iron ball bearings on drive and tail pulleys.
    Sealed, pre-lubricated ball bearings in tread rollers.
END DRIVE–Located on discharge end of conveyor,
   chain guard on left hand side.
SPEED REDUCTION–Sealed worm gear "C" Face
    speed reducer. No. 50 roller chain to drive pulley.
BELT SCRAPER–Mounted in bed section to clean
    underside of return belt.
MOTOR–1 HP–208/230/460/575V–3 Ph.–60
    Hz.–Totally Enclosed “C” Face.
DRIVE PULLEY–8 in. dia. with 1-3/16 in. dia. shaft
    at bearings, machine crowned and fully lagged.
BELT SPEED–Constant 65 FPM.
TAIL PULLEY–6 in. dia. with 1-3/16 in. dia. shaft
    at bearings–self cleaning, crowned		 CAPACITY–Maximum load per linear foot of
    conveyor-25 lbs. NOT TO EXCEED capacity
    in chart.
SNUB IDLER–Adjustable 2-1/8 in. dia. Pre-lubricated
    ball bearings.
FLOOR SUPPORTS–Now supplied as optional.
horizontal conveyors
LOAD CAPACITY CHART
HORIZONTAL CONVEYOR
ROLLER BED @ 65 FPM
HP TOTAL LOAD (LBS.)
UP TO 52' UP TO 102'
1 400 200
2 850 700
OPTIONAL EQUIPMENT
FLOOR SUPPORTS–MS Type floor supports are
    available with a wide range of adjustment. Specify top
    of belt or roller elevation. One support required at
    every bed joint and ends of conveyor. Holes in feet for
    lagging to fl oor. Knee braces recommended above
    MS-6 support.		 O-RING DRIVE CHAIN–With sealed in lubricant
    (Recommended for applications that do not permit
    regular lubrication).
END CAP–A formed steel end cap is bolted to inside
    of conveyor at tail end to keep material from falling off
    end of conveyor (not available with 7 in. extended
    guard rail.)
NOTE: Drive end support non-adjustable up to 16 in.
elevation.
CEILING HANGERS–5/8 in. dia. x 8 ft. long
    unplated rods fully threaded. Other lengths and
    galvanized rods available.
BELT SPEED– Other constant and variable speeds.
    V-Belt drive supplied on speeds under 17 FPM.
    NOTE: Capacity affected with speed changes.
MOTORS–Energy efficient, single phase, other
   characteristics. 2 HP maximum.
CENTER DRIVE–Provides 16 in. of belt take-up.
    Minimum elevation 20 in. Specify location. Minimum
    OAL 66 in.
ELECTRICAL CONTROLS–Non-reversing
    magnetic starters and push-button stations. AC
    variable frequency drive. (see below)
V-BELT DRIVE–V-belt supplied between motor
    and reducer.
Order Online, by Phone, or by E-Mail

~ Add items to your online shopping cart ~
Click a Price of the item you wish to purchase.
PRICES FOR COMPLETE CONVEYOR INCLUDE:
End Drive, Located on Discharge End of Conveyor,
    Chain Guard on Left Hand Side When Standing at
    Infeed Looking Toward Discharge 		1 HP–“C” Face Totally Enclosed Motor (Specify
    Exact Voltage)
Totally Enclosed Chain Guard
Black Trackmate 533 COS 65 FPM Belt Speed
2" Dia. x 12 Ga. Roller in 10 Ga. Formed Frame Less Electrical Controls
"C" Face Speed Reducer - Sealed Worm Gear Less Floor Supports


Overall
Length

Roller
Centers		 Belt Widths
12" 14" 16" 18" 20" 24" 30"
Between Rail Widths 
9" 11" 13" 15" 17" 21" 27"
Overall Frame Widths 
16" 18" 20" 22" 24" 28" 34"
10' 6"
Price Per Ft.
10' 12"
Price Per Ft.
IMPORTANT NOTES...
OTHER LENGTHS INTERMEDIATE BEDS
  Use 10’ overall length, add extra PER FOOT to base
price.		   Use per foot price of width x required length,
supports not included.
OTHER WIDTHS FLOOR SUPPORTS
  For "IN-BETWEEN WIDTHS", use next largest
plus 10%. For widths over 34" OAW, contact us.		   Floor Supports are note included in base price.
There are two (2) stationary floor supports required
for the first bed section and one (1) support required
per bed section thereafter.
NON-STANDARD WIDTHS
  Contact us for lead time.
PRICES FOR OPTIONAL EQUIPMENT
OPTIONAL DRIVES CASTERS
DriveType
BED WIDTHS
16" - 34"
End Drive (C-Face)
End Drive (V-Belt)
  4 in. Dia. 6 in. Dia.
CASTERS Steel Rubber Steel Rubber
Extra Per Support*
*Price includes Knee Braces
NOTE: Casters for HS Supports, contact us.
Brakes For Casters (Add-On per support)*:
4" Dia. Caster................................... $39.20
MOTORS
6" Dia. Caster................................... $125.20
Extra Motor Price for OTHER THAN: 1 HP -
208/230/460/575V - 3 Ph- 60 Hz. - Totally Enclosed		 IMPORTANT NOTES....
Casters are available in either Rigid or Swivel type - Specify.
Speed affects horsepower requirements.
HP
REQ.		 ENERGY EFFICIENT TOTALLY ENCLOSED BRAKE MOTORS
200/208/230/
460/575V
3 PH.-60Hz.		 115/230V
1Ph.-60Hz.		 Holding Brake 208/230/460/575V 3Ph-60Hz Cycling Brake 208/230/460/575V 3Ph-60Hz Cycling Brake 208/230/460/575V 3Ph-60Hz Holding Brake 115/230V 1 Ph.-60Hz.
1
N/C
2
* Note: "High Cycle Brakemotors" are used for indexing and are rated for 30 cycles per minute. Add-On Prices Include 5AC Reducer,
Heavy Duty Motor Base
Plate, and #60 Chain and Sprockets with Taper Bushed Hubs.
** Note: "High Cycle Brakemotor" Add-On Prices Include 5AC Reducer, Heavy Duty Motor Base Plate and Timing Belt Drive.
Note: SSB and D Series are Holding Brakes and are NOT rated for cycling.
Order Online, by Phone, or by E-Mail

~ Add items to your online shopping cart ~
Click a Price of the item you wish to purchase.
CEILING HANGERS
Ceiling Hanger Brackets with (2) 5/8” dia. x 8’-0” long unplated
fully threaded rods ......................................................................
ceiling hangers for conveyors $147.90
Ceiling Hanger Brackets with (2) 5/8” dia. x 8’-0” long galvanized
fully threaded rods .......................................................................
$176.60
Ceiling Hanger Brackets with (2) 5/8” dia. x 10’-0” long unplated fully
threaded rods................................................................................
$218.40
Ceiling Hanger Brackets with (2) 5/8” dia. x 10’-0” long galvanized fully threaded rods.................................................................................
$359.60
Ceiling Hanger Brackets with (2) 5/8” dia. x 12’-0” long unplated fully threaded rods.................................................................................
$362.60
Ceiling Hanger Brackets with (2) 5/8” dia. x 12’-0” long galvanized fully threaded rods..................................................................................
$419.40
Ceiling Hanger Brackets, Less Rods Only .................................... $93.10
Extra Length Rods:
(2) 8’-0” long x 5/8” dia. unplated fully threaded rods ..................
(2) 8’-0” long x 5/8” dia. galvanized fully threaded rods ...............
(2) 10’-0” long x 5/8” dia. unplated fully threaded rods ................
(2) 10’-0” long x 5/8” dia. galvanized fully threaded rods .............
(2) 12’-0” long x 5/8” dia. unplated fully threaded rods ................
(2) 12’-0” long x 5/8” dia. galvanized fully threaded rods .............
Hex Coupling Nuts for Rods .........................................................
Above noted delivery times determined by delivery time of model ordered.
POLY-TIER SUPPORTS
poly tier supports for conveyors
PRICES FOR COMPLETE
SUPPORT INCLUDE:
 IMPORTANT NOTES
• Check for Clearance
• Specify type of conveyor to be used.
• Use in place of LS or MS Supports only.
• Painted Steel Support Legs
• Adjustable Cross pipe Assembly
• Knee Braces (1 set per level of
   conveyor)
• "U" Brackets
• Single Width Conveyor Only
CAPACITY DATA:
1500 lbs..............................................per cross pipe
4500 lbs..............................................per set of legs
(2) TIER POLY-TIER SUPPORTS
36"
42"
48"
54"
60"
66"
72"
78"
84"
90"
96"
102"
108"
114"
120"
(3) TIER POLY-TIER SUPPORTS
36"
42"
48"
54"
60"
66"
72"
78"
84"
90"
96"
102"
108"
114"
120"
Order Online, by Phone, or by E-Mail

~ Add items to your online shopping cart ~
Click a Price of the item you wish to purchase.
FLOOR SUPPORTS
Not Included in Base Price. Use Chart Below for Required Elevation.
"MS" INTERMEDIATE & TAIL SUPPORT
"MSD" DRIVE SUPPORT
Model No. Adjustment to Top of Belt Price Each
*MSD-0-10 10" to 10"
*MSD-0-11 11" to 11"
*MSD-0-12 12" to 12"
*MSD-0-13 13" to 13"
*MSD-0-14 14" to 14"
*MSD-0-15 15" to 15"
*MSD-0-16 16" to 16"
MSD-1 16-9/16" to 18-5/16"
MSD-1.2 17-9/16" to 19-5/16"
MDS-1.4 18-9/16" to 20-5/16"
MSD-2 19-9/16" to 22-5/16"
MSD-3 22-1/16" to 25-1/16"
MSD-4 25-1/16" to 31-1/16"
MSD-5 29-1/16" to 35-1/16"
MSD-6 33-1/16" to 45-1/16"
MSD-7 43-1/16" to 55-1/16"
MSD-8 55-1/16" to 67-1/16"
MSD-9 67-1/16" to 79-1/16"
MSD-10 79-1/16" to 91-1/16"
MSD-11 89-1/16" to 101-1/16"
MSD-12 101-1/16" to 113/1/16"
Model No. Adjustment to Top of Belt Price Each
MSL-1 6-1/8" to 7-1/8"
MSL-2 7-1/8" to 8-7/8"
MSL-3 8-7/8" to 11-1/2"
MS-1 11-1/8" to 12-7/8"
MS-1.2 12-1/8" to 13-7/8"
MS-1.4 13-1/8" to 14-7/8"
MS-2 14-1/8" to 17-1/8"
MS-3 16-3/4" to 19-3/4"
MS-4 19-3/4" to 25-3/4"
MS-5 23-3/4" to 29-3/4"
MS-6 27-3/4" to 39-3/4"
MS-7 37-3/4" to 49-3/4"
MS-8 49-3/4" to 61-3/4"
MS-9 61-3/4" to 73-3/4"
MS-10 73-3/4" to 85-3/4"
MS-11 83-3/4" to 95-3/4"
MS-12 95-3/4" to 107-3/4"
Knee Braces ...........per pair................................... $30.00
NOTE: MS-7 to MS-12 and MSD-7 to MSD-12:
Knee Braces included in price.
NOTE: Knee Braces are required on incline or decline
units with MS-3 or higher supports.
END CAP
Mounts to end of Side Guard ...........each ......... $151.85 DRIVE COMPONENT DEDUCTS
CONSTANT AND VARIABLE SPEEDS
Less Motor Drive, Motor Mount and Guards, but with
Shaft Extension ................Deduct ..................$777.20
Constant C-Face - Within 17-135 FPM ......
................................................................ No Charge
Less Motor Only (1 HP-208/230/460/575V-
Constant V-Belt - Minimum of 4 FPM .......................
3 Ph.-60Hz.)..................Deduct ....................$333.80
........................................ Use V-Belt Drive Add-On
*Less Reducer ..............Deduct ....................$307.40
Constant Speeds Below Those Listed Above ..............
*Less V-Belt Guard, Chain Guard, sheaves and
sprockets when V-Belt drive is supplied. Less chain
guard and sprockets when C-Face drive is supplied.
.............................................................. Contact us
Variable Speed ..See Electrical Controls and Drive
Section below
BELT SCRAPER (BRUSH TYPE)
Maximum Speed .......................................... 65 FPM
Specify location................................... $311.50
ELECTRICAL CONTROLS
GALVANIZING
(See Below)
Contact us.
Order Online, by Phone, or by E-Mail

~ Add items to your online shopping cart ~
Click a Price of the item you wish to purchase.
ELECTRICAL CONTROLS AND DRIVE SECTION
MANUAL START SWITCH or
SAFETY DISCONNECT
 limit switch LIMIT SWITCH, SINGLE POLE,
WITH NYLON ROLLER LEVER
manual start switch
#032.1014......................................... $213.01 #033.2032 & #033.2072..................$555.67
Nema 4
"START-STOP", Nema 1, One direction, 30
AMP, 3 Pole (Single or 3 phase)
LIMIT SWITCH, DOUBLE POLE,
WITH NYLON ROLLER LEVER
limit switch double pole
#033.2033& #033.2072...................$332.11
Nema 4
REVERSING DRUM SWITCH
#032.103.......................................... $854.26
"Fwd-Stop-Rev", Nema 1, for 1-1/2 HP at
115 volts or 2 HP at 230 volts single phase,
or 2 HP max. three phase
PROXIMITY SWITCH, INDUCTIVE,
(METAL SENSING)

#032.210.........................................$205.35
115 Volt AC, two wire with ground, 30mm dia.,
10mm range
foot swtich with guard FOOT SWITCH WITH GUARD
#032.211.........................................$243.09
24 Volt DC, two wire with ground, 30mm dia.,
10mm range
#032.200........................................... $270.29
(Constant Pressure) "On-Off" type, Nema 1,
Pilot Control or 1 HP max. single phase.
PHOTO EYE, ON-OFF TYPE
power cord and plug #EA-000005......................................$1,059.27
Banner Q45 Retro Reflective Photo Eye Kit
with timing module, reflector and mounting
brackets. Photo Eye output is one form C
type relay, Operating voltage
24-250VAC/12-250VDC
POWER CORD AND PLUG (20')
POWER CORD WITH PLUG ONLY 20' LONG
Model No.
Voltage
HP Rating
Prices
EA-039-1A
115/1
1/2-3/4
EA-039-2A
115/1
1
EA-039-3A
115/1
1 1/2
EA-039-4A
230/1
1/2-1
EA-039-5A
230/1
1 1/2-2
EA-039-6A
208-230/3
1/2-2
EA-039-7A
460/3
1/2-2
POWER CORD WITH PLUG 20' LONG WITH MANUAL START SWITCH AND MOUNTING BRACKET
Model No.
Voltage
HP Rating
Prices
EA-039-1B
115/1
1/2-3/4
EA-039-2B
115/1
1
EA-039-3B
115/1
1 1/2
EA-039-4B
230/1
1/2-1
EA-039-5B
230/1
1 1/2-2
EA-039-6B
208-230/3
1/2-2
EA-039-7B
460/3
1/2-2
MOUNTING BRACKETS FOR PHOTO
EYE #033.2122
B-05165...........................................$118.10
AIR PRESSURE SWITCH
#094.191........................................$691.31
Nema 4
EMERG. STOP PULL CORD SWITCH
#032.285 with 032.2851 Turnbuckle
...........................................................$696.08
Nema 4
"RED" EMERGENCY PULL CORD
CABLE AND MOUNTING HARDWARE
#032.281...one side.................$7.44 per / ft.
                  both sides..............$15.87per / ft.
EMERGENCY PUSH BUTTON
#032.284..........................................$279.61
Nema 4
PHOTO EYE, 18MM DIA., DIFFUSED,
(PHOTO PROX.) 115 VOLT, LIGHT
OPERATE, 2-METER CABLE
#032.2113 (100mm range, 3.94")....$1,066.27
#032.2116 (200mm range, 7.87")....$194.14
#033.218 (400mm range, 15.74")....$293.48
NOTE: PRICING LISTED NOT MOUNTED
             OR WIRED 		"PHOTO EYE, RETRO-REFLECTIVE,
(POLARIZED) 24 VOLT DC
#033.2128 with 032.21122 Cable.....$239.09
#032.21122 (Cable Only)...................$72.37
Order Online, by Phone, or by E-Mail

~ Add items to your online shopping cart ~
Click a Price of the item you wish to purchase.
CONTROLLER PRICES
AC VARIABLE SPEED CONTROLLER ONLY
SINGLE PHASE CONTROLLER INPUT
Motor Size 115 Volt 208/230 Volt
1/2 VSC-12-10 VSC-12-12
Price $1,491.84 $1,189.37
1 VSC-12-11 VSC-12-13
Price $1,724.27
2 N/A
VSC-12-14
Price ~
THREE PHASE CONTROLLER INPUT
Motor Size 208/230 Volt 460 Volt 575 Volt
1/2
VSC-01-15
VSC-01-18
VSC-12-29
Price
1
VSC-01-16
VSC-01-19
VSC-12-29
Price
2
VSC-01-17
VSC01--20
VSC-12-30
Price
REPLACEMENT INVERTER DUTY
ENERGY EFFICIENT MOTORS
HP Part No. Price
1/2 032.351 230/460
1 032.353 230/460
2 032.355 230/460
1/2 032.3512 575
1 032.3532 575
2 032.3552 575
IMPORTANT NOTES...
• All above motors are 230 / 460 / 575 Volt, 3 Phase.
• All above V/S Drive Kits include NEMA 1 / IP30
  Junction Box, Controller and Motor.
• Good for cycle rates of up to 15 cycles per minute, at
  1/2 second ramp time, with a maximum speed of 250
  FPM.
• Drawing No. DG-001146.
OPTIONAL: Mounting and Wiring Add-On . . .
(mounted close to the motor)		 $675.20 • When AC Variable Speed Controller is used with a
   Brake Motor, A Brake Relay Kit (EA-068A) is
   required. Add an additional $542.68 for this option.)
Brake Relay Kit (EA-068A).............................. $542.68
ELECTRONIC CLUTCH BRAKE DRIVE PACKAGE
Part No. Description Price
EA-VSC-01-CB 2 HP Electronic Clutch-Brake Kit $5,058.00
OPTIONAL: Mounting and Wiring Add-on .
(mounted close to the motor)		 $675.20
KIT INCLUDES
Part No. Description
VSC-01-20 AC Variable Speed Controller, 460 Volt, 3 Phase
032.345 2 HP 460 Volt, 3 Phase, C-Face Motor TEBC
(Blower Cooled) With 5AC Reducer and #60 Chain
and Sprockets
IMPORTANT NOTES
• Good for cycle rates of up to 60 cycles per minute.
• 1/10 second Accel and Decel time, with 350 FPM
   Maximum Speed.
• 230 or 460 Volt Only, Other Voltages, Contact us.
• Motor Cooling Blower is 115 Volt, 1 Phase, 60 Hz.
• Price Includes 5AC Reducer and #60 Chain and
  Sprockets
Part No. Description
VSC-01-17 AC Variable Speed Controller, 230 Volt, 3 Phase
032.345 2 HP 230 Volt, 3 Phase, C-Face Motor TEBC
(Blower Cooled) With 5AC Reducer and #60 Chain
and Sprockets
Order Online, by Phone, or by E-Mail

~ Add items to your online shopping cart ~
Click the Model No. of the item you wish to purchase.
starter
THIS STARTER LISTING MEETS TYPE "2"
COORDINATION (Defined)
An International Electrotechnical Commission (IEC) term that means: “under short circuit
conditions, the starter shall cause no danger to persons or installation and shall be
suitable for further use.” The only allowable damage to the starter is light contact burning
or tack welding, provided the contacts are separable. Starters meeting this level of com-
ponent protection provides users with less down time and lower replacement costs.
THREE PHASE, IEC COMBINATION MAGNETIC STARTERS
H.P.
MOTOR
DUTY
NON-REVERSING
REVERSING
208 VOLT
230 VOLT
460 VOLT
575 VOLT
PRICE
208 VOLT
230 VOLT
460 VOLT
575 VOLT
PRICE
1/2
STANDARD EASY
CLEAN ENERG. EFF.
$1516.60
$2,023.30
 
 
 
 
 
 
 
 
1
STANDARD EASY CLEAN
ENERG. EFF.
 
 
 
 
 
 
 
 
1-1/2
GEARMOTORS
 
 
 
 
 
 
 
 
2
STANDARD EASY CLEAN
ENERG. EFF.
 
 
 
 
 
 
 
 
SINGLE PHASE, IEC COMBINATION MAGNETIC STARTERS
H.P.
NON-REVERSING
REVERSING
NON-REVERSING
REVERSING
 
115 VOLT
PRICE
115 VOLT
PRICE
230 VOLT
PRICE
230 VOLT
PRICE
1/2
$1,182.40
$2,023.30
$1,435.60
$2,023.30
1
1-1/2
2
• Manual Start-Stop Switch Kit • Start-Stop Push Button Kit, Remote Mounted
EA-000001 ...................................... $242.09 EA-000002....................................... $242.09
Includes: 032.1014 Manual Start Switch, Nema 1,
B-21467 Mounting Bracket with Mounting Hardware		 Includes: 033.1955 Push Button Station, One
Direction, Nema1, B-21467 Mounting Bracket
with Mounting Hardware
• Forward-Reverse-Stop Push Button Kit,
  Remote Mounted
• Up-Down-Stop Push Button Kit, Remote
   Mounted
EA-000003....................................... $440.67
Includes: 033.1965 Push Button Station, Reversing,
Nema1, B-21467 Mounting Bracket with Mounting
Hardware		 EA-000004....................................... $440.67
Includes: 033.1975 Up Down Stop Push Button
Station, Reversing, Nema 1, B-21467 Mounting
Bracket with Mounting Hardware
Order Online, by Phone, or by E-Mail

~ Add items to your online shopping cart ~
Click a Price of the item you wish to purchase.
• “Start-Stop” Push-button Station • “Start-Stop”Push-button Station
033.1955
 $211.23 033.195................................................. $142.50
Remote mounted, Nema 1 To be mounted in Mag Starter Cover
• “Fwd-Rev-Stop” Push-button Station • “Fwd-Rev-Stop”Push Button Station
033.1965 $397.05 033.196.................................................. $490.95
Remote mounted, Nema 1 To be mounted in Mag Starter Cover
• “Up-Down-Stop” Push-button Station
OPTIONAL STARTER CONTROLS
033.1975 $397.05
• Auto Restart Control, 3 Phase, Non-Reversing
Remote mounted, Nema 1
EA-011 ............................................
Includes: Photo Eye (033.2122), Dual Time
Delay Module (033.2172), Combination
Magnetic Starter with extra Contactor
(033.160), and a Control Circuit
Transformer (As Required), & Pushbutton
Station (033.195).
 $3,210.68
IMPORTANT NOTES
• Control Circuit Transformer Included for 115 Volt
  Control Voltage.
• Above starters are in Nema 3, 4 and 12 Enclosures.
• The starters included Safety Disconnect, Overload
  Relay, and Aux. Contacts as required.
• IF AN ORDER IS SUPPLIED LESS MOTOR,
  AND IS SUPPLYING ANY ELECTRICAL
  CONTROLS, THEN MOTOR HP, VOLTAGE,
  PHASE, AND FULL LOAD CURRENT MUST BE
  STATED ON THE ORDER.
• PRICING LISTED IS NOT MOUNTED OR WIRED.
• Auto Restart Control, 1 Phase, Non-Reversing
EA-012 (115 Volt) ...........................
EA-017 (230 Volt) ...........................
Includes: Photo Eye (033.2122), Dual
Time Delay Module (033.2172),
Combination Magnetic Starter with extra
Contactor (033.160), Pushbutton Station
(033.195), and (230 V. Only) a Control
Circuit Transformer (As Required).
Note: Above Price does NOT include
Photo Eye Mounting Bracket.		 $3,253.63
$3,391.27
• Add on $192.70 for the above Push Buttons
  to be Mounted.
• Add on $995.10 for the above Starters and
  Push Button Stations to be Mounted and Wired.
  Supply 20'0" of cable for push button only.
• Mounting Brackets for photo eye
#033.2122
B-05165 ..............................................
$118.10
CONVEYOR WEIGHT TABLES


SIZE TO ORDER
Overall Length
"A"

Bed Length
"L"		 Between Rail Width 9" 11" 13" 15" 17" 21" 27"
Belt Width 12" 14" 16" 18" 20" 24" 30"
Overall Frame Width 16" 18" 20" 22" 24" 28" 34"
"W" 17 1/2" 19 1/2" 21 1/2" 23 1/2" 25 1/2" 29 1/2" 35 1/2"
"B" 28 1/2" 30 1/2" 32 1/2" 34 1/2" 36 1/2" 40 1/2" 46 1/2"
7' 5'


WEIGHTS
(Lbs.)
Weights
Based on
6" Roller
Centers		 410 425 440 460 480 520 570
12' 10' 525 550 570 605 635 685 765
17' 15' 675 705 735 780 825 885 990
22' 20' 790 830 865 920 975 1050 1180
27' 25' 945 990 1035 1105 1170 1260 1415
32' 30' 1055 1105 1155 1235 1315 1420 1600
42' 40' 1320 1385 1445 1550 1655 1785 2020
52' 50' 1585 1665 1740 1870 1995 2150 2440
62' 60' 1845 1940 2030 2185 2335 2520 2880
72' 70' 2110 2215 2320 2495 2670 2885 3280
82' 80' 2375 2495 2615 2815 3015 3255 3705
92' 90' 2645 2680 2715 3040 3365 3635 4135
102' 100' 2905 3050 3195 3445 3690 3985 4540
For 12" Centers Deduct Weights Listed Below
Rollers
Centers		 5' Long Bed Sections 10' Long Bed Sections
BR Width 9" 11" 13" 15" 17" 21" 27" 9" 11" 13" 15" 17" 21" 27"
12" Weight Deduction 10 12 14 16 17 21 26 20 24 28 32 34 42 52
All weights are conveyor weights only. Accessories, crating, etc., are not included.
Belt Conveyors, Conveyor, Conveyor Belt, Low Profile Conveyor, Roller Bed, Troughed Roller, Conveyors, and Slider Bed from your
source for material handling equipment.

Back to Product Category
Home - Order - Search - Quote- Info - About Us - My Account - Shopping Cart