Gilmore-Kramer Company Material Handling Equipment - 1-800-544-3137 - Service - Installation - Custom Fabrication
Home Order Search Quote Info About Us My Account Shopping Cart
    Categories
Back to Product Category

Laminated Rubber Dock Bumpers
laminated rubber dock bumper Features
Tough plies of truck tire material virtually eliminates chipping
    or abrasion, unlike molded rubber, extruded rubber, or wood
    plank bumpers.
Attractive deep black color enhances a neat, professional
    architectural look.
Manufactured under pressure exceeding 1,500 lbs. to absorb
    over 80% of impact force.
Anchor bolts are protected by at least 3" of rubber to prevent
   damage.
Uses / Applications
Available in two models: bumpers with angles for most
    applications -- equipped with 1/4" steel angles on both ends;
    and bumpers with flat plate for use with dock levelers --
    optional 1/4" flat steel plate for one or both ends.
rubber dock bumpers
Have unlimited applications in factories, warehouses and docks.
Vehicle impact protection for loading docks.
Projecting above low docks.
Rub rails at the sides of truck wells.
Wall bumpers to protect against fork lift trucks.
Special construction features to accommodate unusual anchoring
    conditions.

Benefits
Provides maximum protection against
vehicle damage to docks, buildings and cargo.		 Constructed to last and provide years of protection.
Anchored through thick steel angles to provide
stability and shape retention.
Absorbs over 80% of truck umpact and shock to
protect dock and building.
Performs on any truck dock under any weather
condition or prolonged exposure.
Leading bumper sold in the industry today.
Maintenance free. 5 year warranty.
Standard sizes shipped within 24 hours.
Eliminates costly repairs from severe shock to docks.
Material/Thickness

Fabric reinforced rubber pads cut from selected
recycled truck tires.
Rubber pads laminated between structural steel
angles and secured with 3/4" steel tie rods.

 Rubber pads 4-1/2" or 6" thick.
Installation
Structural mounting angles permit welded installations or provide bolting through steel.

Specifications
Furnish and install rubber dock bumpers. Resilient
rubber material of bumpers shall be rubberized-fabric
truck tires cut to uniform size pads and punched to
receive 3/4" supporting rods.		 The anchor leg of angle extends a minimum of
3" beyond the rubber surface at either end and
contains two or three 13/16" anchor bolt holes
as required. (Anchor bolts are supplied separately)
All bumpers must be 4-1/2" or 6" thick (projection
from dock), and closed with two 1/4" structural
angles under approximately 1,500 lbs. of pressure.		 Black finish.
Galvanized exposed metal or all metal available
upon request, surcharges apply.
Laminated Rubber Dock Bumpers
dock bumpers
B4506 Series
B4510 Series
B610 Series		 B4512 Series B4520 Series
B620 Series		 B4524 Series
B624 Series
To order Laminated Rubber Bumpers:
1. Select your required bumper thickness (projection - dimension A) from price table A below, as well as bumper
height (dimension B) and bumper length (dimension C). For level driveways, a 4 1/2" projection is usually adequate.
Note: - If you have an inclined driveway and need assistance selecting the necessary dock bumper
projection, scroll down to the incline driveway chart below price table B.
2. We invite you to let our engineers review your dock bumper application. Complete the dock seal dimension sheet
on our contact page and we will confirm your dock bumper selection.
Table A: Laminated Rubber Bumper Pricing
Order Online, by Phone, or by E-Mail

~ Add items to your online shopping cart ~
Click a Price of the item you wish to purchase.
Model No.
Projection x
Height x Bolt Hole
Centers (Length)
Size (A x B x C)
Vertical
Bolt Hole
Centers
(D)
Rubber
Length
(E)
Overall
Length
(F)
Weight
Price
F.O.B.
Ohio
Factory
Galvanized
Angle
Add-On
4 1/2" Thick Series
B4506-14
4-1/2" x 6" x 14"
3"
10"
16"
18 lbs
B4506-24
4-1/2" x 6" x 24"
3"
20"
26"
28 lbs
B4506-36
4-1/2 x 6" x 36"
3"
32"
38"
42 lbs
B4510-12
4-1/2 x 10" x 12"
6"
8"
14"
25 lbs
B4510-14
4-1/2" x 10" x 14"
6"
10"
16"
26 lbs
B4510-18
4-1/2" x 10" x 18"
6"
14"
20"
34 lbs
B4510-24
4-1/2" x 10" x 24"
6"
20"
26"
45 lbs
B4510-36
4-1/2" x 10" x 36"
6"
32"
38"
66 lbs
B4512-12
4-1/2 x 12" x 12"
4"
8"
14"
31 lbs
B4512-14
4-1/2" x 12" x 14"
4"
10"
16"
32 lbs
B4512-18
4-1/2" x 12" x 18"
4"
14"
20"
41 lbs
B4512-24
4-1/2" x 12" x 24"
4"
20"
26"
56 lbs
B4512-36
4-1/2" x 12" x 36"
4"
32"
38"
82 lbs
B4520-11
4-1/2" x 20" x 11"
6"
7"
13"
42 lbs
B4524-11
4-1/2" x 24" x 11"
4"
7"
13"
51 lbs
B4536-11
4-1/2" x 36" x 11"
4"
7"
13"
85 lbs
6" Thick Series
B610-12
6" x 10" x 12"
6"
8"
14"
29 lbs
B610-14
6" x 10" x 14"
6"
10"
16"
33 lbs
B610-18
6" x 10" x 18"
6"
14"
20"
43 lbs
B610-24
6" x 10" x 24"
6"
20"
26"
58 lbs
B610-36
6" x 10" x 36"
6"
32"
38"
84 lbs
B612-12
6" x 12" x 12"
4"
8"
14"
34 lbs
B612-14
6" x 12" x 14"
4"
10"
16"
41 lbs
B612-18
6" x 12" x 18"
4"
14"
20"
51 lbs
B612-24
6" x 12" x 24"
4"
20"
26"
69 lbs
B612-36
6" x 12" x 36"
4"
32"
38"
105 lbs
B620-11
6" x 20" x 11"
6"
7"
13"
52 lbs
B624-11
6" x 24" x 11"
4"
7"
13"
63 lbs
B636-11
6" x 36" x 11"
4"
7"
13"
100 lbs
Note: 1/4" Flat plates may be substituted for one or both angles.
Galvanized Add on is for exposed metal only - if galvanized ALL metal is required please call for pricing
Overlap Angles available for bumpers 36” bolt hole centers and greater. A 10% upcharge will apply.
Extra-Thick Laminated Rubber Dock Bumpers
extra thick laminated rubber dock bumper Uses / Applications
Where greater "stand out" distance from dock sills is required
    due to steep ramps, canopied docks, overhangs or other
    architectural features.
Features
Consists of tough plies of truck tire fabric which virtually
    eliminates chipping or abrasion.
Benefits
Maintenance free, weather resistant.
Prevents damage to trucks, loading docks and buildings by
    providing greater standout distance from dock sills on steep
    ramps.
Protects dock seals from over-compression.
extra thick dock bumpers Special Notes
Refer to stand-out distance planner to choose
    proper thickness for incline docks.
Extra-Thick bumpers are not warrantied
    due to specialty applications where they
    are used.

B920 Series
B10520 Series
B1220 Series

 B910 Series
B10510 Series
B1210 Series

Material/Thickness
Installation
Uniform size, fabric reinforced rubber pads cut from
selected recycled truck tires in 9", 10-1/2", and 12"
projections.		 Structural mounting angles permit welded
installations or provide bolting through steel (as
opposed to bolting through rubber).

Specifications
Furnish and install extra-thick rubber dock
bumpers. Resilient rubber material of bumpers
shall be rubberized truck tires cut to uniform size
pads, in stand-out thicknesses of 9", 10-1/2" or
12", punched to receive 3/4" steel tie rods.		 Anchor leg of angle extends a minimum of 3"
beyond the rubber surface at either end and contains
two or three 13/16" anchor bolt holes as required.
(Anchor bolts are supplied separately)
Finish for exposed metal parts is either chrome
aluminum lead-free enamel, or hot-dipped
galvanized.
All bumpers are closed with two 1/4" steel formed
angles under approximately 1,500 lbs. of pressure.
1/4" flat plates may be substituted for one or both
angles.
Order Online, by Phone, or by E-Mail

~ Add items to your online shopping cart ~
Click a Price of the item you wish to purchase.
Table B: Extra-Thick Laminated Rubber Bumper Pricing
Model No.
Projection x
Height x Bolt Hole
Centers (Length)
Size (A x B x C)
Vertical
Bolt Hole
Centers
(D)
Rubber
Length
(E)
Overall
Length
(F)
Weight
Price
F.O.B.
Ohio
Factory
Galvanized
Angle
Add-On
9" Thickness
B910-14
9" x 10" x 14"
6"
10"
16"
63 lbs
B910-24
9" x 10" x 24"
6"
20"
26"
98 lbs
B910-36-A3*
9" x 10" x 36"
6"
32"
38"
152 lbs
B920-11
9" x 20" x 11"
6"
7"
13"
103 lbs
10 1/2" Thickness
B10510-14
10-1/2" x 10" x 14"
6"
10"
16"
71 lbs
B10510-24
10-1/2" x 10" x 24"
6"
20"
26"
109 lbs
B10510-36-A3*
10-1/2" x 10" x 36"
6"
32"
38"
167 lbs
B10520-11
10-1/2" x 20" x 14"
6"
7"
13"
109 lbs
12" Thickness
B1210-14
12" x 10" x 14"
6"
10"
16"
76 lbs
B1210-24
12" x 10" x 24"
6"
20"
26"
120 lbs
B1210-36-A3*
12" x 10" x 36"
6"
32"
38"
195 lbs
B1220-11
12" x 20" x 11"
6"
7"
13"
134 lbs
*AD-3 will be supplied unless otherwise specified.
NOTE: All mounting holes correspond to standard 4 1/2" and 6" thick units.
1/4" Flat plates may be substituted for one or both angles.
8" Thickness now available at same price as B910 Series
Center anchorage device AD-3 is recommended for 36” long bumpers, and is included in the price.
Overlap Angles available for bumpers 36” bolt hole centers and greater. A 10% upcharge will apply.
1. Determine (measure) your inclined driveway to establish the amount of driveway rise and your driveway length.
See sketch below.
  bumpers  

"A" Note: In cases where the building wall is setback from the edge of the dock, the actual bumper projection required is
less the building setback. Example: The incline chart indicates a 12" bumper "A" dimension but the building wall is
setback 3", therefore the actual bumper necessary would be 9".
2. Determine the required dock bumper thickness (projection) by using the incline chart below. This chart is designed
to leave the top of the truck approximately either 2" or 6" from the building wall when the truck is fully docked. If
your building does not have dock seals installed then the 2" minimum top clearance (C dimension) can be used to
select the bumper projection. However, if dock seals are installed, it is recommended that a 6" top clearance be
used (C dimension) in order to avoid damage to both building and dock seal.
a. Find your driveway rise in the left column and follow across the chart to a driveway length closest to your actual
measured length. Dimensions in columns C = 2 and C = 6 are the actual calculated thickness of your dock bumpers.
The corresponding bumper series are listed in the adjacent columns. Using either the C = 2" or C = 6" top
clearance series, select your actual dock bumpers from price table A above.
b. Example: Driveway rise is 18", driveway length is 40'. At the intersection of these two rows in the chart, the C = 2
(2" clearance) calculated bumper projection is 6.28" and the suggested dock bumper series is the B610 series.
Refer back to price table A to select the particular B610 series dock bumper length (C) desired and the
corresponding model #.
NOTE: Due to the extensive width of the following chart, it had to be split into two sections
(10' - 40' and 50' - 70').
10'
20'
 30' 40'
Rise Proj.
for
C=2		 For
C=2
Use		 Proj.
for
C=6		 For
C=6
Use		 Proj.
for
C=2		 For
C=2
Use		 Proj.
for
C=6		 For
C=6
Use		 Proj.
for
C=2		 For
C=2
Use		 Proj.
for
C=6		 For
C=6
Use		 Proj.
for
C=2		 For
C=2
Use		 Proj.
for
C=6		 For
C=6
Use
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
3.90 B4510- 7.90 B910-
5.80 B610- 9.80 B10510-
7.70 B910- 11.70 B1210-
9.60 B10510- 13.60  
11.50 B1210- 15.50  
13.40   17.40  
15.30   19.30  
17.20   21.20  
19.10   23.10  
21.00   25.00  
22.90   26.90  
24.80   28.80  
26.70   30.70  
28.60   32.60  
30.50   34.50  
32.40   36.40  
34.30   38.30  
36.20   40.20  
38.10   42.10  
40.00   44.00  
41.90   45.90  
43.80   47.80  
45.70   49.70  
47.60   51.60  
49.50   53.50  
51.40   55.40  
2.95 B4510- 6.95 B910-
3.90 B4510- 7.90 B910-
4.85 B610- 8.85 B910-
5.80 B610- 9.80 B10510-
6.75 B910- 10.75 B1210-
7.70 B910- 11.70 B1210-
8.65 B910- 12.65 B1210-
9.60 B10510 13.60  
10.55 B1210 14.55  
11.50 B1210 15.50  
12.45 B1210 16.45  
13.40   17.40  
14.35   18.35  
15.30   19.30  
16.25   20.25  
17.20   21.20  
18.15   22.15  
19.10   23.10  
20.05   24.05  
21.00   25.00  
21.95   25.95  
22.90   26.90  
23.85   27.85  
24.80   28.80  
25.75   29.75  
26.70   30.70  
2.63 B4510- 6.63 B610-
3.27 B4510- 7.27 B910-
3.90 B4510- 7.90 B910-
4.53 B4510- 8.53 B910-
5.17 B610- 9.17 B910-
5.80 B610- 9.80 B10510
6.43 B610- 10.43 B10510
7.07 B910- 11.07 B1210-
7.70 B910- 11.70 B1210-
8.33 B910- 12.33 B1210-
8.97 B910- 12.97  
9.60 B10510- 13.60  
10.23 B10510- 14.23  
10.87 B1210- 14.87  
11.50 B1210- 15.50  
12.13 B1210- 16.13  
12.77   16.77  
13.40   17.40  
14.03   18.03  
14.67   18.67  
15.30   19.30  
15.93   19.93  
16.57   20.57  
17.20   21.20  
17.83   21.83  
18.47   22.47  
2.48 B4510- 6.48 B910-
2.95 B4510- 6.95 B910-
3.43 B4510- 7.43 B910-
3.90 B4510- 7.90 B910-
4.38 B4510- 8.38 B910-
4.85 B610- 8.85 B910-
5.33 B610- 9.33 B10510-
5.80 B610- 9.80 B10510-
6.28 B610- 10.28 B10510-
6.75 B910- 10.75 B1210-
7.23 B910- 11.23 B1210-
7.70 B910- 11.70 B1210-
8.18 B910- 12.18 B1210-
8.65 B910- 12.65 B1210-
9.13 B910- 13.13  
9.60 B10510- 13.60  
10.08 B10510- 14.08  
10.55 B10510- 14.55  
11.03 B1210- 15.03  
11.50 B1210- 15.50  
11.98 B1210- 15.98  
12.45 B1210- 16.45  
12.93   16.93  
13.40   17.40  
13.88   17.88  
14.35   18.35  
50' 60' 70'
Rise Proj.
for
C=2		 For
C=2
Use		 Proj.
for
C=6		 For
C=6
Use		 Proj.
for
C=2		 For
C=2
Use		 Proj.
for
C=6		 For
C=6
Use		 Proj.
for
C=2		 For
C=2
Use		 Proj.
for
C=6		 For
C=6
Use
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
2.38 B4510- 6.38 B910-
2.76 B4510- 6.76 B910-
3.14 B4510- 7.14 B910-
3.52 B4510- 7.52 B910-
3.90 B4510- 7.90 B910-
4.28 B4510- 8.28 B910-
4.66 B4510- 8.66 B910-
5.04 B4510- 9.04 B910-
5.42 B610- 9.42 B910-
5.80 B610- 9.80 B10510-
6.18 B610- 10.18 B10510-
6.56 B910- 10.56 B1210-
6.94 B910- 10.94 B1210-
7.32 B910- 11.32 B1210-
7.70 B910- 11.70 B1210-
8.08 B910- 12.08 B1210-
8.46 B910- 12.46 B1210-
8.84 B910- 12.84  
9.22 B910- 13.22  
9.60 B10510- 13.60  
9.98 B10510- 13.98  
10.36 B10510- 14.36  
10.74 B10510- 14.74  
11.12 B1210- 15.12  
11.50 B1210- 15.50  
11.88 B1210- 15.88  
2.27 B4510- 6.27 B910-
2.54 B4510- 6.54 B910-
2.81 B4510- 6.81 B910-
3.09 B4510- 7.09 B910-
3.36 B4510- 7.36 B910-
3.63 B4510- 7.63 B910-
3.90 B4510- 7.90 B910-
4.17 B4510- 8.17 B910-
4.44 B4510- 8.44 B910-
4.71 B4510- 8.71 B910-
4.99 B610- 8.99 B910-
5.26 B610- 9.26 B910-
5.53 B610- 9.53 B10510-
5.80 B610- 9.80 B10510-
6.07 B610- 10.07 B10510-
6.34 B610- 10.34 B10510-
6.61 B910- 10.61 B10510-
6.89 B910- 10.89 B1210-
7.16 B910- 11.16 B1210-
7.43 B910- 11.43 B1210-
7.70 B910- 11.70 B1210-
7.97 B910- 11.97 B1210-
8.24 B910- 12.24  
8.51 B910- 12.51  
8.79 B910- 12.79  
9.06 B910- 13.06  
2.32 B4510- 6.32 B910-
2.63 B4510- 6.63 B910-
2.95 B4510- 6.95 B910-
3.27 B4510- 7.27 B910-
3.58 B4510- 7.58 B910-
3.90 B4510- 7.90 B910-
4.22 B4510- 8.22 B910-
4.53 B4510- 8.53 B910-
4.85 B610- 8.85 B910-
5.17 B610- 9.17 B910-
5.48 B610- 9.48 B910-
5.80 B610- 9.80 B10510-
6.12 B610- 10.12 B10510-
6.43 B610- 10.43 B10510-
6.75 B910- 10.75 B1210
7.07 B910- 11.07 B1210
7.38 B910- 11.38 B1210
7.70 B910- 11.70 B1210
8.02 B910- 12.02 B1210
8.33 B910- 12.33 B1210
8.65 B910- 12.65  
8.97 B910- 12.97  
9.28 B910- 13.28  
9.60 B10510- 13.60  
9.92 B10510- 13.92  
10.23 B10510- 14.23  
Special Order Products - Contact US
ARCHITECTURAL SPECIFICATIONS - Laminated Rubber Dock Bumpers
Furnish and install rubber dock bumpers as manufactured by Bondor Division of FS Industries, W. Greenwich, RI
Model No(s)______________. Resilient rubber material of bumpers shall be rubberized-fabric truck tires cut to
uniform size pads and punched to receive 3/4" (19.1 mm) supporting rods.
•
All bumpers must be ___________________ thick (projection from dock), and closed with two 3" x 3" x 1/4"
(76.2 mm x 76.2 mm x 6.35 mm) structural angles under approximately 1,500 pounds (680.4 kg) of pressure.
The angles are welded to 3/4" (19.1 mm) rods at one end and closed with threaded rod and nut at the other end.
•
The anchor leg of angle extends a minimum of 3" (76.2 mm) beyond the rubber surface at either end and contains
two or three 13/16" (20.6 mm) anchor bolt holes as required. (Anchor bolts are supplied separately.)
•
•
The finish for exposed metal parts shall be either chrome aluminum lead-free enamel, hot-dipped galvanized.
Dock Bumper, Dock Bumpers, Laminated Dock Bumper, Laminated Dock Bumpers, Loading Dock Bumper, Loading Dock Bumpers,
Rubber Dock Bumper, Rubber Dock Bumpers, Truck Dock Bumper, Truck Dock Bumpers, and Laminated Rubber Bumpers from your
complete source for material handling equipment.

Back to Product Category
Home - Order - Search - Quote- Info - About Us - My Account - Shopping Cart